How to make coasters using scrap fabric

Today I’m using the scrap fabric from my bunting project and making coasters.
What you will need:
Scrap Fabric
Bias Binding
Sewing Machine
Pencil or Pen


Step 1. To make one coaster that is 10cm in diameter, you will need 14 strips of fabric that are 2.5cm in width (a seam allowance of 5 mm has already been added) and at least 11cm in length.

Steps 2 – 6 need to be repeated as 7 strips will be used to make the front of the coaster and the 7 remaining strips will be used to make the back of the coaster.

Step 2. Put two strips of fabric together with the right sides facing in. With your sewing machine sew along one of the edges.

Step 3. Open the connected strips like a book and attach a third piece along one of the edges and sew. When this is done connect a fourth strip onto the third strip and then carry on doing the same until you have attached the seven strips onto each other. This is what it should look like from the back.

Step 4. Lay the connected strips flat and iron on the wrong side of the fabric. To keep this piece tidy, make sure you iron all the seams to one direction as pictured below.

Step 5. Trace a circle 10cm in diameter onto your interfacing. For this step you can use a compass or in my case I found the lid of a Hershey’s Kisses tin was the perfect size. I’m sure you can find circular objects around the house if you don’t have a compass either.

Cut the circle out of your interfacing and iron onto the back of your strips. This will make your coaster more rigid.

Step 6. Cut along the outline of the interfacing. You should end up with a neat circle, the front being your fabric strips and the back being interfacing.

Step 7. As noted in the beginning of the tutorial, repeat steps 2 through to 6 in order to produce a front and back for your coasters. Once this is done, attach the two circles together with the interfacing facing inwards. Sew along the circumference of the coaster closely to the edge so that the stitch can be covered by the bias binding.

Step 8. You will need a strip of bias binding that is approximately 32cm in length. Wrap the bias binding around the edge of your coaster and sew. This finishing touch will hide the rough edges and prevent your coaster from fraying.


You have one coaster… now make 5 more 😉 Remember to keep all your scraps from this project, you never know when they’ll come in handy!

How to make a Babooshka Brooch using scrap felt and fabric


What you will need:
Babooshka Pattern
Scrap Fabric and/or Felt
Craft Glue
Thread (2 Colours)
Sewing Needle
Brooch Pin
Step 1.  Using the pattern provided find the appropriate sized scrap felt/fabric and cut out all the different pieces.
Step 2. With craft glue, attach piece D onto piece B. When they are dry, glue them onto piece A as shown.
Step 3. Piece E is glued on like so.
Step 4. Hand sew the features on the face leaving enough room for the hair. The cheeks can be made using piece G or they too can be hand stitched. Note: This part requires a lot of care and patience if you are using piece G therefore hand stitching the cheeks may be an easier alternative.
Step 5. Using a little bit of glue attach the face (H) onto the body followed by the hair (C) and then the scarf knot (F).
Step 6. Use a running stitch to further secure all the pieces and add detail to the brooch. Follow the figure below.
Step 7. Fasten the brooch pin to the right side of piece I using glue and/or thread. This is the back of the brooch.
Step 8. Put the front and back together and secure using a blanket stitch. Use double thread to make stronger, more eye catching detail.

Now you have a Babooshka brooch to attach to whatever you like!

How to Make a Felt Deer

Hello! For my first post EVER I’m going to give you a tutorial on how to make a little felt deer.
What you will need:
Deer Pattern
Felt (3 colours)
Hand Sewing Needle
Wadding (Stuffing)
Craft Glue
Step 1. Cut out the felt pieces following the pattern provided. The pattern is for a deer that is approximately 12 cm tall. Simply shrink or enlarge the pattern to accommodate your needs.
Step 2. Stitch the two tail pieces together then stitch the Inner body to the Outer body as shown below. You can use an ordinary running stitch but to add some extra detailing I have decided to use a blanket stitch.Step 3. Stitch the two outer body pieces together, starting at the end of the last stitch shown in step 2 (the deer’s chest). At the tail point fold the tail in half lengthwise and add it to the body, stitching over it until you reach the first stitch shown in step 2 (the deer’s rear).

Step 4. Fill the deer with wadding through the opening at the inner body. Use a chopstick or something similar to gently push the wadding down the legs and neck. Take a considerable amount of care at this step as felt can be very fragile and you want your deer to be evenly padded. When you have completed this, stitch the deer closed.

Step 5. Stitch the head pieces to the centre head, starting at the tip of the nose and ending at the neck. Fill the head with wadding.

Step 6. Put some glue at the tip of the neck on both the body and head. Place the neck inside the head, higher if you want a short deer and lower if you want a tall deer. When you have decided on the placement, stitch the head closed starting from the neck and ending at the tip of the nose.

Step 7. With glue, add the ears, eyes, nose and any other desired details such as body spots.
To personalise your felt deer you can use other materials such as putting lace or ribbon around the neck and/or using sequins for the spots. It’s up to you how creative you want to be!


I like to take my deers to the park and make them kiss.